How To Lay A Laminate Flooring?

One of the benefits of laminate flooring is its easy installation, making it one of the most popular floor coverings. However, we do not all have the same DIY skills, for this reason, it is good to know the recommendations of the experts on how to do the assembly correctly.

 

The installation of laminated flooring requires the use of certain tools and utensils, such as a false square, hammer, jigsaw, sander, flame thrower, among others. As with the installation of floating parquet, in this case some materials are also necessary, among which are adhesive tape, skirting boards, insulation and of course wooden sheets. Let’s see step by step how to put the laminate flooring.

 

Take measurements

This step is essential to be able to buy the correct amount of materials, so that you can make a fair investment. As a general rule, it is better than over a little, but any excess implies a greater expense, for this reason you must pay attention when taking the measures. A good trick is to divide the area into different zones, for example, room, closet and entrance, in this way it is easier to take the measurements of each space with a tape measure and calculate the necessary materials, ensuring that nothing is missing.

 

Clean the work area 

The laminate flooring can be installed on almost any surface, however, the space must first be cleaned, not only to carry out the work in a comfortable and organized way, but also to obtain a more professional result. For example, if you have removed a carpet, nails and glue residue may remain on the floor, so you should proceed to clean the entire surface. The idea is that there are no obstacles in the work area, so the skirting must also be removed.

 

Prepare the soil

This is a very important part of laying laminate flooring. Once you have a clean surface, you must prepare the floor to place the wood with greater confidence. In this sense, you must make sure that there are no damp areas caused by leaking pipes, otherwise, you will have to repair them and let them dry before installing the wooden floating floor.

If you are going to place the wood on concrete, remember that this material always keeps some humidity, so one of the DIY tricks in this regard is to apply an asphalt-based treatment all over the floor, since the wood can deteriorate and even accumulate microorganisms due to humidity. This is more common in predominantly cold climate areas.

 

When you are sure that the floor is free of moisture, it is time to place the layer of insulation, which serves as a protector for both acoustics and temperature. This is a material made of felt, polyethylene or polystyrene that you can easily find in physical stores and on the internet. You just have to cut it into strips of different sizes and cover the floor using masking tape to join the pieces. If you don’t know how to put laminate flooring on tile, the good news is that the procedure is the same.

 

Place the slats

Although the laminated floorboards can be fixed with nails and adhesives, most of the current models come with a click system, which makes the job much easier. If you wonder where to start putting laminate flooring, you should know that experts recommend starting at one of the corners of the place, however, you have to leave a margin of expansion on the edge of the wall, which can be 10 mm or simply place small pieces of the same wood between the slats and the wall, as wedges. This space prevents deformations in the floor from appearing due to the natural effect of the wood expansion.

 

 

If the slats do not have a click system, then you must apply special wood glue in the groove of the next table and place it next to the first one. Afterwards, you can hit with a hammer firmly but gently until the slats fit correctly. To protect the material from impacts, you can place a wooden block between the blade and the hammer. Also, it’s important to have a damp cloth on hand to quickly wipe up excess glue.

However, if you have chosen slats with a click system, then the installation is much simpler. In theory, it is a matter of inserting the male side of the second piece into the groove of the first at an angle of approximately 25º, to then lower it. As for the direction of placement of the laminate flooring, it depends on your preferences, but it is considered simpler and more aesthetically attractive to choose the longest side of the room and place the slats in that direction. It is worth mentioning that these modern sheets are easy to remove and there is no need to damage the material during future disassembly. 

You can make different designs with the wooden slats, but the best thing to do if you are beginners is to start with a complete sheet, make the second row with half of this measurement and the third with a plank that measures half of what it measures. the second. Thus, it is possible to create a pattern that is easy to remember and with a sober finish.

 

Install the skirting board

It is recommended to put a skirting board at the end, but if you do not want to disassemble the old skirting board, you also have the option of using a skirting board, which is used to cover the existing one. Another solution is to place a wooden or PVC bead, which has a rounded finish and serves to cover the joint between the skirting board and the floor. To install these pieces you can use mounting adhesive.

 

Final finish

It is normal that when you finish you see sawdust shavings and other remains of the work, therefore, it is advisable to vacuum the entire surface. In this sense, it is good to know that some Nilfisk , Dyson and other brand vacuum cleaners have special nozzles with wood brushes. Finally, you can apply a special product to shine and preserve the material.

Leave a Comment